Alternating current (AC) is used for power line transmission and for high power devices like appliances and lights. The characteristics of AC make it ideal for transmission over long lines and for delivering large amounts of power for relatively unregulated uses, such as generating heat and light. Lower power appliances and devices require the closely regulated control of direct current power (DC). As a normal house is supplied with AC, it must be converted to DC for many uses. Use these tips to learn how to make an AC DC converter.
Steps
1 Select a transformer. A transformer contains 2
magnetically coupled wire windings. One winding is called the primary.
The primary is driven by the main AC supply. The other winding is called
the secondary. The secondary serves as the power input to the AC DC
converter. This transformer and all of the other items needed to build
the AC DC converter are readily available at electronic stores and hobby
stores.
- Size the transformer windings. AC mains provide 120 volts AC. If 120 volts AC were directly converted to a DC voltage, the resulting DC voltage would be far too high a voltage for use by appliances and devices. The primary and secondary windings of the transformer are scaled to each other in order to produce a lower voltage on the secondary winding.
- Choose a secondary winding. The AC output of the secondary winding should be rated as the same voltage of DC that is being created.
2 Wire the primary winding of the transformer to the main AC supply. This transformer connection has no polarity and may be connected either way.
3 Connect the secondary winding of the transformer to a full wave bridge rectifier package.
The transformer connections and the connections to the marked inputs of
the rectifier package have no polarity and may be connected either way.
- Build a full wave rectifier. This rectifier can be built up from 4 discrete rectifying diodes, rather than using a rectifier bridge package. The diodes will be marked to show a positive (cathode) end and a negative (anode) end. Connect the 4 diodes into a loop. Connect the cathode of diode 1 to the cathode of diode 2. Connect the anode of diode 2 to the cathode of diode 3. Connect the anode of diode 3 to the anode of diode 4. Connect the cathode of diode 4 to the anode of diode 1.
- Wire the discrete rectifier to the transformer secondary. The transformer secondary should be connected to the cathode of diode 3 and the cathode of diode 4. There is no required polarity for these connections. The positive output of the rectifier is at the point where the cathodes of diodes 1 and 2 join. The negative output of the rectifier is at the point where the anodes of diodes 3 and 4 join.
4 Attach a smoothing capacitor. Attach a polarized
capacitor across the output connections of the rectifier. The positive
terminal of the polarized capacitor must connect to the positive output
of the regulator. This capacitor should be sized such that the
capacitance in farads (F) is equal to (5 times the current to be
supplied by the AC DC converter) divided by (transformer secondary
rating times 1.4 times frequency). Frequency varies from country to
country, but is typically either 50 Hertz (Hz) or 60 Hertz.
5 Provide the final regulation. Choose a commercially
available voltage regulator designed to control the output of the AC DC
converter to the desired output voltage. The regulator will be a 3-pin
device. The regulator pins will be a common, an input from the smoothing
capacitor and an output of the regulator. This regulator output also
will be the final output of the completed AC DC converter.
- Wire the regulator as directed in the manufacturer's data sheet. There probably will be a noise suppression capacitor specified in the regulator manufacturer's data sheet. Acquire and install that capacitor per the manufacturer's data sheet for the regulator.
Sign up here with your email
3 comments
Write commentsI appreciate your article. You truly share relevant and extraordinary knowledge. Thank you for keep sharing these valuable thoughts.
Reply38 WATT DC/DC CONVR : 494GC : ALCATEL-LUCENT
AC-DC PWR UN 950W : ES660C : ALCATEL-LUCENT
208/240 V0LTS AC-DC : 364A3 : ALCATEL-LUCENT
Both AC and DC devices have their own pros and cons. Personally, I like both.
ReplyAlso check https://inverterreview.com/tag/12v/ as well.
ReplyConversionConversion EmoticonEmoticon